[Full-Version] 2022 Updated NACE Study Guide NACE-CIP1-001 Dumps Questions
Newest NACE-CIP1-001 Exam Dumps Achieve Success in Actual NACE-CIP1-001 Exam
The preparation of the NACE CIP1-001 exam can be done with the best solution
You should be ready to face the tough competition of the NACE CIP1-001 exam. We provide the best solution for the preparation of the NACE CIP1-001 exam. You can easily download the NACE CIP1-001 Dumps. The practice test helps you to easily understand the pattern of the exam. It also helps the candidates to know the difficulty level of the topics covered in the NACE CIP1-001 exam. We provide the latest version of the NACE CIP1-001 practice test. The updated version of the NACE CIP1-001 practice test helps the candidates to easily pass the NACE CIP1-001 test. Update questions help you to easily prepare for the NACE CIP1-001 exam. You can easily prepare for the NACE CIP1-001 test by using the NACE CIP1-001 study material.
The salary of a NACE CIP1-001 certified professional can be found here.
The Average salary of different countries of NACE CIP1-001 Certified professionals is given below:
- UK 49527.40 Pounds
- India 4982421.50 INR
- USA 67,000 USD
NEW QUESTION 36
Solvents are added to coating formulations to
- A. provide color.
- B. dissolve binders and form liquid coatings.
- C. increase film permeability.
- D. decrease film permeability.
Answer: B
NEW QUESTION 37
On a blast-cleaned surface, Ian ultraviolet light is generally used to detect
- A. grease and oil
- B. inhibitor residues
- C. soluble chemical salts
- D. sulfates
Answer: A
NEW QUESTION 38
Whenever dissimilar metals must join, the most common practice is to
- A. coat all connected dissimilar metals.
- B. avoid coating all connected dissimilar metals.
- C. provide cathodic protection to prevent corrosion,
- D. provide anodic protection to prevent corrosion.
Answer: A
NEW QUESTION 39
Check abrasive blast pressure close to the
- A. substrate
- B. blast pot
- C. blast nozzle
- D. compressor
Answer: C
NEW QUESTION 40
Fine cracks in the surface of a coating that rarely reach the substrate are called
- A. cracking.
- B. blistering.
- C. alligatoring.
- D. checking.
Answer: D
NEW QUESTION 41
ISO SA 2.5 is defined as:
- A. Light Blast Cleaning
- B. Thorough Blast Cleaning
- C. Very Thorough Blast Cleaning
- D. Near White Metal Blasting
Answer: C
NEW QUESTION 42
You are the NACE Inspector on a job where the Owner's specification requites you to perform a twice daily check of blast pressure at the nozzle. It is now day 30 on the job and all of your readings have been within compliance. The Contractor complains that these checks taking up much time and in view of the compliant results they are unnecessary.
Your FIRST preferred course of action is to:
- A. Keep doing the checks and consult the Owner's representative for direction
- B. Skip the checks as you are. confident the blast pressure is OK
- C. Skip the checks and just record the same readings as you have been getting
- D. Keep doing the checks regardless
Answer: A
NEW QUESTION 43
What is used to determine compressed air cleanliness?
- A. Profilometer
- B. Needle pressure gauge
- C. Psychrometer
- D. Blotter test
Answer: A
NEW QUESTION 44
Dew point is the temperature at which
- A. condensation occurs.
- B. water freezes.
- C. the air is saturated.
- D. humidity decreases
Answer: A
NEW QUESTION 45
The form of corrosion that has the largest potential for unexpected catastrophic failure is:
- A. Atmospheric Corrosion
- B. Galvanic Corrosion
- C. General Corrosion
- D. Localized Corrosion
Answer: B
NEW QUESTION 46
You are the NACE Inspector on a job where ISO ST 3 has been specified. The Contractor normally works to SSPC standards and been referencing SSPC SP 3.
Could this have any impact on the final surface preparation appearance?
- A. It depends on which power tool the Contractor selects
- B. Yes, because the 'two standards are not equivalent
- C. No, because there is no real difference in the standards
- D. It depends on which hand tool the Contractor selects
Answer: C
NEW QUESTION 47
ASTM Standards are applicable:
- A. When specified
- B. In Asia
- C. In North America
- D. In the USA
Answer: A
NEW QUESTION 48
If the specifier does not identify a restriction level in accordance with SSPC PA 2, the default restriction level is:
- A. Level 4
- B. Level 1
- C. Level 2
- D. Level 3
Answer: D
NEW QUESTION 49
An inspectors personal log book should contain:
- A. No comments regarding the application team
- B. The inspector's personal opinions of the application team
- C. Subjective comments re ding the application team
- D. Objective comments regarding the application work
Answer: A
NEW QUESTION 50
Excess moisture during holiday testing can cause erroneous indications by creating a path across the surface of the coating to pinholes previously detected, or directly to the signal return connection.
This is often referred to as:
- A. monitoring
- B. transitioning.
- C. telegraphing.
- D. juxtaposing.
Answer: C
NEW QUESTION 51
If the project specification DOES NOT state the specific DFT measurement standards, the inspector should use
- A. a recognized industry standard like SSPC-PA 2 that is broadly accepted
- B. a detailed checklist and document the lack of a standard.
- C. NACE 2/SSPC SP10
- D. their best judgment based on similar projects and specifications.
Answer: A
NEW QUESTION 52
In a non-convertible coating the role of the primary solvent is to:
- A. To make the coating flow out better
- B. To control the evaporation rate
- C. To dissolve the resin
- D. To promote faster cure
Answer: B
NEW QUESTION 53
When holiday testing is required the Inspector is always required to enforce NACE SP 0188:
- A. True
- B. False
Answer: A
NEW QUESTION 54
You have just received your NACE CIP Level 1 certification when you are asked to supervise a team of uncertified field pipeline inspectors.
Your FIRST preferred course of action is to:
- A. Meet with the prospective employer to determine the scope of your role
- B. Review the NACE Attestation prior to making a decision
- C. Advise the prospective employer that you cannot accept the position
- D. Accept the assignment without hesitation
Answer: A
NEW QUESTION 55
If inspectors identify issues of non-conformance during an inspection, they should
- A. inform both the Contractor and the inspector's supervisor so they can take appropriate corrective actions
- B. wait until the final report is being prepared to identify the issues in writing so they are fully documented
- C. perform additional tests secretly to ensure there are no other potential issues at the site
- D. instruct the contractor's personnel in how to correct the issue so the project is not delayed
Answer: A
NEW QUESTION 56
ISO SA 3 is directly equivalent to:
- A. NACE No. 3/SSPC SP 6
- B. NACE No. 2/SSPC SP 10
- C. NACE No. 1/SSPC SP 5
- D. None of the above
Answer: D
NEW QUESTION 57
Surface profile describes:
- A. The level of surface roughness required after abrasive blasting
- B. The general condition of the surface required after abrasive blasting
- C. The level of surface cleanliness required after abrasive blasting
- D. The initial condition of the surface prior to abrasive blasting
Answer: A
NEW QUESTION 58
A single application coating film has a measured dry film thickness (DFT) between 4 and 5 mils (between 100 and 125 microns). The volume solids of the coating immediately before application were 67%, What wet film thickness (WFT) was applied?
- A. 8 to 10 mils (200 to 250 microns)
- B. 5 to 6 mils (125 to 150 microns)
- C. 10 to 12 mils (250 to 300 microns)
- D. 6 to 7 mils (150 to 175 microns)
Answer: D
NEW QUESTION 59
Inspection documentation is important because:
- A. Owners use the documentation for a variety of purposes
- B. a) & b)
- C. a) only
- D. It is the only deliverable item provided by the inspector
Answer: A
NEW QUESTION 60
Inspector's daily reports are used:
Select All That Apply
- A. To aid in arbitration between the contractor and client
- B. By the contractor to estimate the amount of work done that day
- C. To help in cases of a coating failure
- D. To provide continuity between inspectors
Answer: A,B,C,D
NEW QUESTION 61
......
Updated NACE NACE-CIP1-001 Dumps – Check Free NACE-CIP1-001 Exam Dumps: https://torrentpdf.actual4exams.com/NACE-CIP1-001-real-braindumps.html